Excitation side
The excitation filter sets the spectrum reaching the sample; also check its leakage in the detection band.
Small-animal imaging · Fluorescence & bioluminescence · Near-infrared
For fluorescence, bioluminescence and near-infrared imaging — matched to low-light detection and multi-band collection.
For small-animal optical imaging we configure excitation filters, emission filters and beam-splitting elements around the fluorescent probe or bioluminescent reporter, the light source and the camera response. Passband and blocking design balance target-signal collection, background suppression and multi-channel separation.

Define the imaging mode first, then the combination of excitation, emission and beam-splitting elements.
| Imaging mode | Signal origin | Filter priorities |
|---|---|---|
| Fluorescence imaging | Probe or fluorescent protein excited by an external source | Excitation band selection, emission collection and excitation blocking |
| Bioluminescence imaging | Biochemical reaction of a reporter system | Broad-band collection or selected emission bands as required |
| Near-infrared fluorescence imaging | NIR probe emission after excitation | Matching probe spectrum, tissue background and detector response |
| Multispectral imaging | Target signal collected in several bands | Channel coverage, response calibration and spectral separation |
| NIR-II / SWIR research imaging | Emission of the corresponding NIR probe | Band fit across filters, lens and detector as one chain |
Near-infrared and multispectral describe a wavelength range or an acquisition method; they can be combined with fluorescence or bioluminescence modes.
In vivo optical signals are usually weak, while background arises from reflected and scattered excitation light, tissue autofluorescence and overlapping probes. Filter design has to consider signal level, background position and acquisition method together.
| System concern | Filter design focus |
|---|---|
| Weak target signal | Passband position, effective bandwidth and transmission |
| Background from reflected or scattered excitation | Blocking performance at the emission side over the real excitation range |
| Tissue autofluorescence reducing contrast | Target-to-background spectral relationship and multi-band acquisition plan |
| Overlapping signals from several probes | Channel choice and the acquisition set required for unmixing |
| Response varies across a large field | Beam cone angle, angle of incidence and clear-aperture uniformity |
| Background rises during long exposures | Check light leaks, material background and system stray light |
Filters reduce part of the non-target light but cannot remove every background component that shares the target band. Image quality depends on probe, tissue, illumination, lens, camera and processing method.
Fluorescence imaging needs excitation and emission sides to work together; bioluminescence needs no external excitation and may stay broad-band or add band selection.
The excitation filter sets the spectrum reaching the sample; also check its leakage in the detection band.
The emission filter defines what the camera sees and must block the real excitation range.
A coaxial path can add a dichroic as designed; reflective and transmissive illumination are drawn separately.
No excitation filter is needed without external excitation; broad-band collection preserves photon flux.
Bioluminescence collection needs no external excitation light. Broad-band collection makes the most of photon flux; when reporter signals must be separated or spectral information is needed, band-resolved detection can be added by design.
Selection directions below; bands and sizes are example placeholders — actual values depend on the probe, medium and equipment.
GFP, red fluorescent proteins
Cy5.5, Cy7, IRDye series, ICG
Firefly luciferase and other reporters
Combinations of fluorescent or luminescent reporters
Related research probes
Probes of the same family, different protein variants or different substrate combinations can have different spectra. A name alone does not define the passband.
Grouped by optical function; excitation, emission and beam-splitting elements are selected together.
Selects the fluorescence excitation band
Defines the collected target-signal range
Collects signal beyond the edge
Combines or separates different wavelength paths
Sequential multi-channel image capture
For the corresponding research imaging bands
A multi-band filter wheel set means several filters forming one acquisition scheme; whether a single multi-bandpass design applies has to be assessed against the signal separation method.
Choose the band from real probe emission, tissue transmission and camera response — not only from the emission peak measured in solution.
A wider band usually collects more signal but may also admit more background. A narrower band helps separate some spectral components but reduces photon flux.
Check excitation leakage in the detection band and emission blocking of the excitation light; do not judge a single filter by its peak value alone.
A suitable band reduces part of the background; where target and background spectra overlap, controls, multi-band acquisition and algorithmic processing are also needed.
Incidence angle varies across the field. Provide filter position, lens parameters and beam cone angle, then check band shift and image response uniformity.
Assess possible background, reflection or vignetting from substrate, coating, adhesive and housing under the real illumination and collection conditions.
These are the ranges we normally produce. Requirements beyond them can be evaluated from drawings; final values are confirmed by sample and datasheet.
| Specification | Range we can produce |
|---|---|
| Excitation wavelengths | 405, 488, 561, 638, 760, 808 nm |
| Emission range | Visible to NIR-II (1000-1700 nm) |
| Multiband filters | Simultaneous imaging across several fluorescence channels |
| Blocking depth | OD5-OD6 for strong background suppression |
| Transmission | T >70% for high collection efficiency on weak signals |
| Large aperture | φ50-φ100 mm to match large-field cameras |
| Background control | Reduces excitation scatter; tissue autofluorescence overlapping the target needs probe and spectral handling |
Recommended: overlaid excitation and emission spectra, passband transmission and blocking curves, multi-channel coverage charts, dimensional drawings and filter-wheel mounting illustrations, plus environmental and background test data with traceable evidence. Charts distinguish schematic, typical, guaranteed and measured values.
Near-infrared probes are used in small-animal in vivo optical imaging. Selection should combine tissue absorption and scattering, probe brightness, light source and detector response — a longer wavelength alone does not define performance.
| Stage | What to check |
|---|---|
| Probe and light source | Confirm real excitation efficiency and emission range. |
| Filters and lens | Confirm transmission in the target band and excitation rejection. |
| Detector and acquisition | Confirm effective response, noise and exposure conditions. |
NIR-II / SWIR proposals list concrete working ranges rather than a band name in place of technical specifications.
Filters and beam splitters configured for the imaging mode, probe and instrument layout.

Excitation and emission filters set around the probe spectrum and illumination layout.

Detection path configured for broad-band or band-resolved collection.

Multi-channel acquisition supplies the information needed to separate target from background.

Bands matched across probe, lens and camera.

Optical scheme set by the labelling method and experimental goal; filter performance is not presented as an experimental conclusion.
Requirements → spectral & mechanical assessment → sample set → imaging verification → specification release
Collect imaging mode, probe spectra, light source, camera, lens and mounting conditions.
Confirm passbands, blocking ranges, working angles and multi-channel combinations.
Prepare samples according to the assessment.
Prefer standard fluorescent materials, optical phantoms or suitable reference samples; check background, excitation leakage, field uniformity and channel cross-response. Multispectral systems further verify calibration and unmixing.
Define spectral and mechanical specs, lot consistency and delivered documentation.
Real instrument photos, sample reports and delivered documentation are used here.