ISO 9001 Certified Manufacturer 360° Factory Tour

Colour measurement · Tristimulus

Color Difference Meter Filters

Matched chromaticity response — the optical basis of colour consistency checks

For tristimulus colour-difference meters and colour inspection modules. Working from the illumination source, the detector response and the measurement conditions of the instrument, we design chromaticity-matched filter sets, NIR rejection filters and intensity-control elements for colour measurement, colour difference comparison and module integration.

  • Chromaticity matching
  • Multi-channel sets
  • Non-target rejection
  • Batch consistency
Chromaticity matching Channel response fixed together with the detector
Multi-channel sets Channel count set by the design
Batch consistency A variable in the final dE
Handheld colorimeter, colour reference chart and optical filter set
Channel structure and element positions are schematic and vary between models

What is a colorimeter filter?

A colorimeter filter is a spectral weighting element in a colour measurement channel. By setting a different transmission at different wavelengths it shapes, together with the detector and the other optics, the channel response the system needs, and the system then converts the measured signals into colour parameters.

A tristimulus colorimeter approximates the colour matching functions of a standard observer with several optical channels, obtains or derives XYZ tristimulus values and converts them into L*a*b* and similar parameters. Comparing with a standard sample gives the colour difference through the chosen formula.

Matching here is not simply letting one filter pass red, another green and another blue. What has to match is the shape of each channel response as a whole: the main response region, the edges, the tails and the relative level between channels.

A colorimeter filter therefore cannot be described completely by centre wavelength and bandwidth. Design and acceptance normally also need the target transmission curve, the detector response data and the calibration conditions of the system.

Scope note: "colorimeter" may also refer in the market to a spectrophotometric instrument that computes colour differences. This page covers the filter-based tristimulus approach; grating instruments are described on the spectrophotometric colour page.

Working principle: from reflected light to a colour difference value

A filter does not change colour; it changes the weight each wavelength carries in the detection channel.

  1. 01

    The source illuminates the sample

    Under the specified source the sample reflects each wavelength to a different degree. The light entering the instrument depends on both the source spectrum and the reflectance of the sample.

  2. 02

    The filters weight the spectrum

    Reflected light enters several detection channels. Transmission of each channel filter varies with wavelength, so different bands contribute with different weight. The aim is not to make every channel as narrow as possible, but to make the channel response suit the colour measurement task.

  3. 03

    The detector outputs channel signals

    The detector has its own spectral sensitivity. Even with identical filters, a detector with a different response can change the channel output. For a linear system the signal of one channel can be read as the sum over wavelength of incident power × filter transmission × other optical transmission × detector response.

  4. 04

    Colour is computed and compared with the standard

    After suitable calibration the channel signals are converted into colour parameters and the difference from the standard sample is computed. A tristimulus instrument and a spectrophotometer obtain colour information differently; the former normally does not deliver the full reflectance spectrum of the sample.

Illumination and sample Detection channels · where the response is formed Source visible + NIR incl. UV Sample reflects per λ may fluoresce Collection geometry beam shaping Filter set chromaticity, multi-ch per-λ weighting Detector own response channel signals Channel signals → calibration → XYZ → L*a*b* / dE ① Each filter weights the spectrum; filter and detector together form the response ② Channel count and layout vary with the design; this drawing does not fix them
Light source → sample → collection optics → chromaticity filter set → detector → calibration and colour computation → colour difference Multi-channel designs differ in structure; the schematic does not fix the number or arrangement of the actual channels.

A channel signal is a weighted sum over wavelength: change the detector and the filter has to be re-confirmed; change the filter and the calibration has to be re-confirmed.

Core concept: chromaticity matching is not plain RGB separation

Separation filters tell colours apart; chromaticity filters make the colour calculation come out right.

A plain separation filter mainly separates colour bands from one another. A chromaticity-matched filter has to consider whether the channel response meets the requirements of the colour calculation. The difference shows up in the objective, the metrics and the design basis, and it moves verification from the single element to the instrument.

Item Plain RGB separation Chromaticity matching
Main objective Separate the red, green and blue regions Obtain a channel response suited to the colour calculation
Key metrics Passband, bandwidth and blocking Full curve, channel response and matching error
Design basis A target colour or a wavelength band Standard observer target, detector and optical path
Verification Inspect the spectrum of each element Element spectra together with system sample validation

Note that the colour matching functions are not all simple single peaks. The CIE 1931 x̄ function, for example, has two response regions. A real system may approximate the target with a composite filter structure, separate channels or signal combination, so the X channel cannot be treated as one ordinary red bandpass element.

Filter transmission and channel response are two different things. Confirm which channel response the instrument should end up with, then work back to the filter design from the detector behaviour.

Target response Detector response Combined channel Response two lobes rises toward red combined 400 500 600 700 Wavelength (nm) ※ Design schematic, not measured data; shapes and channel count by agreement
Channel response is set by filter and detector together: target response, detector sensitivity and the combined response (design schematic, not measured data)

Product options: choosing the structure by channel function

The structures below are grouped by where they sit and what they solve; the combination depends on the instrument architecture, the channel count and the samples.

Option A

Chromaticity-matched filter set

Multi-channel filter combinations designed from the target chromaticity response and the detector behaviour, for tristimulus colorimeters and colour inspection modules. Both the spectral shape of each channel and the energy balance and batch spread between channels have to be controlled. The number of elements and the structure follow the system design; they are not fixed at three simple single-layer parts.

Selection focus
Target response, full transmission curve, channel balance, set consistency.
Option B

NIR rejection filter

Where the detector still responds noticeably in the near infrared, NIR rejection can be evaluated to reduce the effect of non-target radiation on the colour channels. The visible red-end signal that is needed has to be kept, so strengthening the NIR cut does not truncate the measurement band.

Selection focus
Visible passband, red-edge transition, NIR blocking, angular behaviour.
Option C

Illumination-side spectral correction filter

Adjusts the illumination spectrum to work with the existing source, or controls the UV content in a specified design. A source correction affects every detection channel. For samples with fluorescent components, the effect of the illumination spectrum on fluorescence excitation also has to be considered, not only the visible transmission of the receiving filter.

Selection focus
Source spectrum, target illumination, useful flux, stability.
Option D

Channel balance and neutral density filters

Used to adjust channel energy, match the detector dynamic range or build a test path. Beyond the attenuation level, the spectral flatness over the working band has to be assessed: attenuation that differs with wavelength can change the weighting between channels.

Selection focus
Attenuation, flatness, relative channel output, reflection.
Option E

Compact filter assemblies

Depending on the module space, single elements, combined elements or multi-channel mounting assemblies are evaluated. Design has to work from the actual incidence angle, clear aperture, channel isolation and assembly method. When the material, the cement layer or the packaging changes, the effect on the spectrum and on long-term stability should be checked again.

Selection focus
Dimensions, assembly datum, channel positions, incoming inspection.

The five options are not mutually exclusive: one instrument may combine a detection-side channel set with illumination-side spectral correction, so each position should be confirmed separately.

Specifications and customisation notes

The table lists the parameters to confirm item by item; fabrication ranges and performance figures are confirmed against validated fabrication and inspection capability.

Parameter Customisation Explanation
Instrument use Object colour difference or another colour measurement task Different tasks have different illumination and detection conditions
Chromaticity target Specified standard observer and channel targets State which target functions and calculation are used
Illumination conditions Source spectrum, operating state and range Object colour measurement has to include the illumination
Detector response Actual model and spectral response data Sets the response of filter plus detector
Channel count Set by the optical and algorithmic design Three tristimulus values do not require three separate filters
Target transmission curve Curve and permitted deviation by wavelength More suitable for chromaticity matching than a centre wavelength
Channel matching error Normalisation, weighting and evaluation method agreed State whether the figure refers to the filter or the whole channel
Useful transmission Keep a usable signal in the target response region Balanced against matching error and signal-to-noise
Non-target rejection UV, NIR or other ranges agreed Designed from the actual source of interference
Incidence conditions Nominal angle, angular spread and polarisation Consistent with the actual module structure
Substrate and thickness Assessed for spectrum, strength and assembly Absorption and thickness can shift the curve
Outline and clear aperture Defined by drawing Distinguish the outline from the guaranteed optical area
Set consistency Permitted spread between channels and between batches What matters is the result of the set
Environmental stability Temperature, humidity, light exposure and cleaning Verified against the actual use case
Inspection and delivery Spectra, dimensions, channel marking and batch records Inspection conditions and set relationship stated

Chromaticity-matched filters are best designed and validated as a set. Once the target response, the source spectrum and the detector data are available, the curve of each element, the channel ratio and the acceptable deviations can be defined, and instrument performance assessed on representative samples.

clear aperture Single element outline vs clear aperture Filter set channel layout and balance Compact assembly isolation and datum ※ Three delivery directions by assembly; dimensions, coated face and orientation per drawing
Three delivery directions: single element, combined filter set and compact assembly (structure schematic; dimensions per drawing)

Clarifications: reading colour and colour difference figures

These terms come up most often in colorimeter discussions, and are most often treated as the same thing.

Q1

XYZ tristimulus values

Three numbers describing a colour. They depend on the colorimetric system and the measurement conditions, and are not the same as the RGB drive values of a display.

Q2

L*a*b* parameters

L* is lightness; a* runs red to green; b* runs yellow to blue. Their calculation needs a reference white, so a general value cannot be derived from the filter output alone.

Q3

Colour difference dE

Expresses the difference between two colours, but is not a single fixed formula. dE*ab, CIEDE2000 and others compute differently, so any comparison has to state the formula and the measurement conditions.

Q4

Repeatability

Agreement between repeated measurements of the same sample under defined conditions on one instrument. Good repeatability does not by itself mean the result has no systematic bias.

Q5

Inter-instrument agreement

Difference between instruments measuring the same sample under the same conditions. Filter batch consistency is one factor; source, geometry, detector and calibration also contribute.

Q6

Spectral mismatch

Difference between the actual channel response and the target chromaticity response. Mismatch may favour some samples and penalise others, so a single white tile cannot prove the full colour capability.

Applications and adaptation points

Requirements differ widely with the object measured, so start from what is compared and under which conditions.

Application Typical use Filter design focus
Portable colorimeters Incoming, in-process and outgoing colour checks Compact size, set matching, batch stability
Plastics and masterbatch Colour consistency of the same material Channel response and representative sample validation
Coatings and paints Colour matching and in-process comparison Spectral matching and measurement geometry
Textiles Batch-to-batch dye comparison Illumination conditions, fluorescent samples
In-line colour inspection Continuous colour monitoring in production Temperature, source drift, long-term stability
Custom colour recognition modules Sorting, recognition and process monitoring Channels and response set by the task

Measuring self-luminous objects such as displays and LEDs is a related application, but the spectral range, dynamic range and calibration samples have to be defined separately; the object-colour approach cannot simply be reused.

Custom process

Requirement definition → channel response design → filter samples → assembly matching → instrument validation → specification release

  1. 1

    Requirement definition

    Sample types, measurement geometry, source and the target colorimetric conditions.

  2. 2

    Response design

    Filter set curves and channel ratios derived with the detector data.

  3. 3

    Sample inspection

    Spectra, dimensions and set marking checked.

  4. 4

    Assembly matching

    Mounting angle, channel isolation and energy distribution checked.

  5. 5

    Instrument validation

    White, dark, saturated and applicable special samples evaluated.

  6. 6

    Specification release

    Batch tolerances, inspection method and delivery requirements agreed.

Frequently asked questions

Source Factory In-house coating lines, no middlemen
Ready to Ship Standard items dispatched same or next day
Quality Guaranteed 100 % inspected, spectral report included
Express Delivery DHL / FedEx worldwide