ISO 9001 Certified Manufacturer 360° Factory Tour

Infrared optics · Materials and processes

Infrared Lens Fabrication and Coating

Five infrared materials, with forming, grinding, single-point turning and coating

OOTEE Optics fabricates germanium, silicon, chalcogenide glass, ZnSe and ZnS lenses for infrared optical systems. Depending on the material, surface form and drawing, we select forming, grinding and polishing or single-point diamond turning, with AR coating, DLC protective coating and optical inspection in support.

Materials Ge, Si, chalcogenide glass, ZnSe, ZnS
Surface forms Spherical, aspheric and applicable diffractive surfaces
Aperture example Ge single-point turning φ4–300 mm
Tolerance example Ground or turned surface figure PV 0.1–0.6 μm

Each figure applies to a specific material, process and part condition; it does not mean all maximum values are reached simultaneously at the largest aperture.

From material forming to coating and inspection

Infrared lens fabrication is not only about controlling diameter and thickness: the optical surface must meet the designed shape, and the two surfaces must keep the specified relationship to each other and to the mechanical datums. Different parts call for different process combinations:

01

Forming and milling

Establish the blank outline and preliminary curve, leaving stock for finishing.

02

Grinding and polishing

Progressively correct the optical surface, controlling figure error and surface defects.

03

Single-point diamond turning

Generate the optical surface through precise machine motion and tool path, suited to aspheric and diffractive needs of the relevant material.

04

Optical coating

Configure AR, protective or reflective coatings for the working band and environment.

05

Inspection and review

Check dimensions, figure, centration and spectral performance to form the acceptance basis against the drawing.

Drawing and material review → blank preparation / forming → grinding or single-point turning → dimension and figure inspection → coating → final review

A part usually cycles between processes: figure is re-measured after polishing, spectra after coating. A deviation in any step is carried into the next.

Materials and aperture ranges

Aperture ranges are listed per material and process; the main selection basis is the material plus process combination.

Material Grinding & polishing aperture Single-point turning aperture Focus on this page
Germanium (Ge) φ4–200 mm φ4–300 mm Lens fabrication with AR and AR+DLC
Silicon (Si) φ4–200 mm φ4–200 mm Lens fabrication with 3–5 μm coating
Chalcogenide glass φ4–140 mm φ4–180 mm Forming, grinding, turning and coating
Zinc selenide (ZnSe) φ4–200 mm φ4–200 mm Lens fabrication with AR coating
Zinc sulfide (ZnS) φ4–200 mm φ4–200 mm Lens fabrication with AR coating

Material choice must match the optical design, working band, ambient temperature and mounting conditions. The same material in a different grade, thickness or process route may support different tolerances and coating conditions. Please specify the grade and the drawing.

Chalcogenide coating data covers grades such as IRG201, IRG202, IRG204, IRG205 and IRG206, shown here as material and coating matching guidance; machinability of a given grade depends on the blank condition.

Chalcogenide glass forming

Depending on the chalcogenide blank and lens geometry, we establish the part outline by cutting, rough blank moulding and milling, preparing it for grinding or single-point processing. Rough blank moulding here is a forming step and is not equivalent to precision moulding of the final optical surface.

Chalcogenide glass forming and moulding equipment
Item Capability listed Inspection
Aperture range φ4–200 mm Per dimensional inspection requirements
Radius deviation ±0.002 mm Interferometer
Center thickness deviation ±0.005 mm Micrometer
Diameter deviation ±0.002 mm Laser diameter gauge
Surface quality 80-50 Visual inspection
Surface figure PV 0.8–1.5 μm Interferometer

The forming stage is mainly about blank dimensions, curvature and finishing stock. Its figure and surface quality should be listed separately from final finishing values so customers can judge the delivery state of each step.

Grinding and polishing capability

Depending on material and part geometry we use high polishing, low polishing or double-side polishing. Grinding and polishing must control surface shape while respecting center thickness, diameter and downstream assembly requirements.

Infrared lens grinding and polishing line
Item Chalcogenide Germanium Silicon ZnSe / ZnS
Aperture range φ4–140 mm φ4–200 mm φ4–200 mm φ4–200 mm
Radius deviation ±0.002 mm ±0.002 mm ±0.002 mm ±0.002 mm
Center thickness deviation ±0.005 mm ±0.005 mm ±0.005 mm ±0.005 mm
Diameter deviation ±0.002 mm ±0.002 mm ±0.005 mm ±0.002 mm
Surface quality grade 40-20 to 80-50 40-20 to 80-50 40-20 to 80-50 40-20 to 80-50
Surface figure PV 0.1–0.6 μm 0.1–0.6 μm 0.1–0.6 μm 0.1–0.6 μm

The ranges describe assessable capability. Acceptance values for a specific part depend on material, aperture, curvature, thickness and the effective inspection aperture.

Single-point diamond turning

Single-point diamond turning generates the designed surface through precise relative motion between tool and workpiece. For aspheres the tool path is defined from curvature, conic constant and aspheric coefficients; for diffractive surfaces the structure parameters and inspection requirements must also be defined.

Single-point diamond turning lathe
Item Chalcogenide Germanium Silicon ZnSe / ZnS
Aperture range φ4–180 mm φ4–300 mm φ4–200 mm φ4–200 mm
Radius deviation ±0.002 mm ±0.002 mm ±0.002 mm ±0.002 mm
Center thickness deviation ±0.005 mm ±0.005 mm ±0.005 mm ±0.005 mm
Diameter deviation ±0.002 mm ±0.002 mm ±0.005 mm ±0.002 mm
Surface quality grade 60-40 to 80-50 40-20 to 80-50 40-20 to 80-50 40-20 to 80-50
Surface figure PV 0.1–0.6 μm 0.1–0.6 μm 0.1–0.6 μm 0.1–0.6 μm

Single-point turning equipment

Machine Throughput Qty
Single-point diamond lathe LK100 5000 mm / day 3
Single-point diamond lathe L200 8000 mm / day 1

Standard and high-precision tolerances

The table below is the general tolerance basis, used to judge whether a requirement calls for a dedicated process route; it is not mixed with the per-material tables above.

Item Standard High precision (reference)
Diameter tolerance 0.01–0.03 mm 0.003–0.005 mm
Surface quality 60-40 / 80-50 40-20
Thickness tolerance ±0.03 mm ±0.005 mm
Power N 3–5 0–1
Irregularity ΔN 0.5–1 0.2–0.3
Sagitta tolerance ±0.03 mm ±0.005 mm
Radius range R5–R∞ R5–R∞
Aspheric figure error 0.5–1 μm 0.1–0.2 μm

Diameter tolerance must be stated with upper and lower deviation on the drawing; power, irregularity and aspheric figure should be accompanied by test wavelength, effective aperture and evaluation method. High-precision values are confirmed per part and are not a blanket guarantee for all materials and sizes.

The general φ5–260 mm range describes the applicable production window; the main table on this page uses material-plus-process apertures so it is not confused with figures such as φ300 mm for germanium single-point turning.

Infrared coating capability

AR coatings reduce surface reflection loss in a specified band; DLC diamond-like carbon coatings suit applications with surface durability requirements. Different coating designs affect transmission, reflection and environmental behaviour differently, so they are chosen against the actual application.

Substrate Coating / band Average transmission
Germanium Dual-side AR, 8–12 μm ≥97%
Germanium 4–12 μm coating design approx. 96%
Silicon 3–5 μm coating design approx. 98%
Germanium AR+DLC, 8–12 μm ≥91%
Silicon AR+DLC, 3–5 μm ≥85%
Chalcogenide 8–12 μm or 8–14 μm, per grade and design ≥96%
ZnSe AR coating Per band and drawing
ZnS AR coating Per band and drawing

Coating types available

  • AR (anti-reflection) coatings.
  • AR+DLC combined stacks.
  • Gold high-reflection coatings.
  • Aluminium high-reflection coatings.
  • Beamsplitter and other functional coatings assessed against the optical path.

Typical coating spectra

Each curve corresponds to one substrate, one band and one coating design and cannot stand for the whole product range; delivered parts are accepted against measured curves from the same batch.

Germanium, dual-side AR, 8–14 μm, average transmission approx. 96%
Germanium, dual-side AR, 8–14 μm, average transmission approx. 96%
Silicon, dual-side AR, 3–5 μm, average transmission approx. 98%
Silicon, dual-side AR, 3–5 μm, average transmission approx. 98%
Germanium, AR+DLC, 8–14 μm; the DLC layer adds some absorption
Germanium, AR+DLC, 8–14 μm; the DLC layer adds some absorption
Silicon, AR+DLC, 3–5 μm
Silicon, AR+DLC, 3–5 μm

Figures reflect current capability. Each product must state substrate grade, thickness, single or dual-side stack, angle of incidence and measurement conditions; "approx. 96%" and "approx. 98%" remain approximate and are not minimum guaranteed values.

Processing and inspection equipment

Equipment counts reflect the present production line and describe process coverage, not a per-piece capacity commitment.

Processing equipment

Process Machine and model Qty
Forming Centering machine SPCM-M1 5
Forming CNC lathe 2
Forming Rough blank moulding furnace 5
Grinding Four-axis tilt machine HT120.4DF 2
Grinding Push-pull machine LP-4NP 5
Grinding Upper lapping machine ZHB-8 10
Grinding Lower lapping machine 10
Grinding Six-axis tilt machine HT120.6DF 2
Grinding Single-axis / chamfering machine ZKM05A 5
Grinding Low polishing machine QJP25.4B 4
Single-point turning Single-point diamond lathe LK100 / L200 4

Inspection equipment and use

Inspection Equipment Note / wavelength range
Surface figure Multiple interferometers (Fuji 601, SD-60, G150-2, AC150 and others) Figure assessed per part and inspection setup
Profile PGI profilometer Curved and aspheric profile checks
Centration TC-1 and other centering stations Relationship between optical and mechanical datums
Spectrophotometry LAMBDA950 spectrophotometer 190–3300 nm
Reflectance MSP-108P reflectometer 390–1050 nm
IR spectroscopy SPECTO-TWO FTIR 1400–20000 nm (1.4–20 μm)
Spectrophotometry Xinrui UV-IR photometer 200–1100 nm

An instrument wavelength range does not mean the same inspection accuracy is reached for every material and accessory configuration. Final inspection items must correspond to the actual drawing and test conditions.

Reading the tolerance table

On one drawing, several values constrain each other. Understand the scope of each term before discussing feasibility.

Aperture and clear aperture

Outer diameter is for mechanical assembly; the clear aperture is the region where optical performance must be guaranteed. Clamping, chamfer and edge zones may not count as clear aperture and should be marked separately on the drawing.

Radius of curvature R

Radius describes how strongly a spherical surface curves. An asphere additionally needs conic constant, higher-order coefficients, axis orientation and aperture — one R value cannot define manufacturing. R∞ is commonly used for a flat.

Center thickness and sagitta

Center thickness is the separation of the two surfaces at the defined center point; sagitta is the height of a curved surface relative to a stated datum. They control different geometry and cannot substitute for each other.

Surface figure PV

PV is the difference between the maximum and minimum error relative to the agreed reference or design surface. State the effective inspection aperture, fitting method and terms excluded. Figure PV describes shape error and is not surface roughness.

Surface quality 40-20, 60-40, 80-50

These grades describe scratch and dig requirements and must be used with an agreed inspection standard, illumination and judgement method. They cannot be converted directly into Ra or Rq roughness values.

Power N and irregularity ΔN

Power describes the interference fringe deviation under the stated test conditions; irregularity addresses local deviation. Both must be read with the test wavelength, method and aperture — fringe counts are not micrometre values.

Centration

Centration describes deviation between optical axis, surface and mechanical datum. Angular decentration and a positional offset in micrometres are different quantities; acceptance must state the datum and measurement definition.

Custom fabrication notes

Machinability of an infrared part depends on the combination of material grade, geometry and inspection conditions. Define the inputs before discussing tolerances.

Category Details
Material Material name, grade and material certificate requirements
Geometry Outer diameter, center thickness, edge thickness, chamfer and clear aperture
Optical form Flat, spherical, aspheric or diffractive definition
Tolerances Figure, surface quality, thickness, centration and other tolerances
Operating conditions Working band, angle of incidence, ambient temperature and mounting
Coating AR, DLC, metal reflection or other stack
Acceptance Inspection method, sampling plan and delivered documents

We assess material, process, inspection and coating fit against the customer drawing and operating conditions. For prototypes and volume orders, key tolerances, process route and acceptance conditions are confirmed separately.

Deliverables can include dimensional records, figure inspection results, spectral curves, visual inspection and batch identification as agreed. Any parameter without defined test conditions is completed during technical review.

Send a drawing
Source Factory In-house coating lines, no middlemen
Ready to Ship Standard items dispatched same or next day
Quality Guaranteed 100 % inspected, spectral report included
Express Delivery DHL / FedEx worldwide