ISO 9001 Certified Manufacturer 360° Factory Tour

Analytical instruments · UV–Vis–NIR

Spectrophotometer Optical Filters

Matched to the analytical band, the spectral purity and the detection path

For spectrophotometers and photometric analysis modules. Working from the source spectrum, the monochromator structure, the detector response and the measurement requirement, we provide bandpass, order-sorting, out-of-band rejection and intensity-control filter solutions for fixed-wavelength detection, continuous scanning and multi-band switching paths.

  • Band selection
  • Order sorting
  • Out-of-band rejection
  • Filter wheel matching
UV–Vis–NIR Common analytical coverage
Order sorting Suppress overlapping orders
Filter wheel Multi-channel sets
Spectrophotometer optical path with filters and a filter wheel (schematic)
Path and element positions are schematic and vary between models

What is a spectrophotometer filter?

A spectrophotometer filter is a spectral-selection or intensity-control element used in a photometric measurement system. By selective transmission, reflection or absorption it changes the spectral composition or the intensity of the light entering the following path, so that the effective measuring light matches the instrument design.

A spectrophotometer compares the light intensity before and after the sample to obtain transmittance and absorbance. In a typical scanning instrument a grating or prism with slits forms the monochromator and carries the main wavelength-selection function; the filter, depending on structure, blocks higher-order diffracted light, limits non-target bands or adjusts intensity. A spectrophotometer should therefore not be described universally as "separating wavelengths with a narrowband filter".

In fixed-wavelength photometers or some multi-channel detection modules, a bandpass filter can itself be the main wavelength-selecting element, forming one or several detection channels as a single part or in a filter wheel. These designs work differently from a continuous-scanning spectrophotometer, so the instrument architecture should be clarified first.

The "filters" covered on this page fall mainly into the following types:

Product type Main function
Measurement bandpass filter Selects a fixed detection band
Order-sorting filter Suppresses non-target light overlapping the wanted diffraction order
Long-pass, short-pass and combined filters Restricts light outside a defined band from the following path
Neutral density filter Attenuates intensity as required
Filter wheel elements Support scanning or multi-channel switching
Reference filter for verification Used for specific performance checks; requires reference values and traceability

Filters and monochromators divide the work: the monochromator selects wavelengths continuously, while filters handle order sorting, out-of-band rejection and intensity control.

Measurement principle: how the filter affects photometry

From comparing intensities to reading absorbance, the filter determines which wavelengths enter the path and how much of them.

  1. 01

    The source provides the light for measurement

    The source emits over a range of wavelengths. The system has to select the range that matches the analytical method and control unwanted radiation entering the measurement channel.

  2. 02

    The wavelength-selecting system defines the effective band

    Scanning instruments usually select wavelengths with a monochromator; fixed-wavelength modules can use a bandpass filter. Filters can also work together with the monochromator to handle grating order overlap.

  3. 03

    The system compares sample and reference intensity

    Taking intensities corrected for dark signal and the appropriate reference: transmittance T = I / I0, absorbance A = -log10(T). For example T = 0.1 means 10% transmittance, corresponding to A = 1.

  4. 04

    Non-target light can affect the result

    With strongly absorbing samples the transmitted light in the target band is already weak, so even a small amount of stray light that the sample does not absorb can visibly bias the reading and produce a low absorbance. Stray-light control therefore matters for high-absorbance measurement.

T = I / I0 A = −log10(T) T = 0.1 means 10% transmittance, giving A = 1
Source broadband Mono- chromator slit / grating Filter assembly order sorting Sample absorbance Detector intensity compare Photometric calculation: T = I / I0 , A = -log10(T) ① Monochromator selects wavelengths; the filter handles order sorting, blocking and intensity ② Element positions differ in array and double-beam instruments
Light source → wavelength selection and filter assembly → sample → detector → photometric calculation A simplified schematic of a common scanning path; array, double-beam and other structures place the elements differently.

Sample absorbance and the OD used to describe blocking attenuation share a similar logarithmic expression, but they describe different quantities under different acceptance conditions and must not be treated as one product specification.

Core concept: what is order sorting?

A grating separates wavelengths, but different diffraction orders can also overlap in the same direction.

For example, when the system selects first-order light at a given wavelength, second-order light at half that wavelength may travel in the same direction. If the source emits at that shorter wavelength and the detector responds to it, a non-target signal can appear.

An order-sorting filter blocks these unwanted wavelengths while keeping the target measurement band, helping to reduce the effect of order overlap. A long-pass filter is one common implementation.

Scanning over a wide range may require several filters used in segments. The switching wavelengths of the filter wheel and the effective transmission ranges of adjacent filters should be designed together to avoid obvious energy jumps or baseline discontinuities at a switch.

Grating dispersion first order λ (target band) second order λ/2 (unwanted) order-sorting filter Detector target band only ① First-order target light passes to the detector ② Half-wavelength second-order light travels the same way and is blocked; low source output there reduces the risk
Order sorting: first-order target light passes while half-wavelength second-order light is blocked (design schematic, not measured data)

Order sorting addresses overlap between diffraction orders in the same direction; it does not replace stray-light control, baffling or optical path design.

Product options: matching different instrument functions

The structures below are grouped by function; the actual combination depends on the instrument architecture, band range and assembly conditions.

Option A

Fixed-wavelength bandpass filter

Transmits within a defined band and blocks light over agreed ranges on both sides, for fixed-wavelength photometric modules and multi-channel analytical paths. The design has to consider centre wavelength, guaranteed passband, FWHM, passband transmission and out-of-band blocking together; a centre wavelength alone does not define a detection channel.

Adaptation focus
Analytical band, source spectral width, signal level, channel-to-channel consistency.
Option B

Order-sorting long-pass filter

Keeps the target scanning range and suppresses short-wave light that may form higher-order overlap. Several filters can be designed as a set for a scan range and used in a filter wheel.

Adaptation focus
Cut-on edge, short-wave blocking range, transmission in the target region, switching strategy.
Option C

Out-of-band rejection filter

Uses long-pass, short-pass or bandpass structures according to source and detector characteristics to reduce the share of specified non-target bands entering the path. Filters address interference that can be separated by wavelength; in-band scatter, mechanical light leaks and internal reflections still need baffling, masking and path design.

Adaptation focus
Actual interfering band, target signal loss, mounting position.
Option D

Neutral density filter

Attenuates intensity within an agreed working band for detector dynamic-range matching, energy adjustment or a specific test configuration. "Neutral" means attenuation as constant as possible over the specified band; it does not mean identical transmission from UV to NIR.

Adaptation focus
OD, spectral flatness, where the reflected light goes, working intensity.
Option E

Filter wheel element set

A set of filter elements whose spectra and mechanical fit are designed together for a scan range or a set of detection channels. Beyond single-part performance, the mounted clear aperture, angle, position repeatability, channel marking and switching intervals all matter.

Adaptation focus
Dimensional consistency, mounting datum, channel order, set inspection.

Technical parameters and customisation

The table lists the parameters to confirm item by item during customisation; capability figures are confirmed against the project requirement and validated fabrication and inspection results.

Parameter Customisation Explanation
Working band Set by the actual UV, visible or NIR requirement The instrument scan range cannot be used directly as the guaranteed range of one filter
Filter structure Bandpass, long-pass, short-pass, ND or combined Selected according to the element function in the system
Centre wavelength Target value, definition and permitted deviation Mainly for bandpass products
FWHM Set by passband shape and detection need Not the same as a guaranteed passband at a specified high transmission
Blocking edge Cut-on / cut-off position and criterion State the transmission level used to define the edge
Passband transmission Minimum, average or peak These three cannot be substituted for one another
Out-of-band blocking Transmission limit or OD for specified bands The wavelength range and transition region must be stated
Spectral flatness Variation within the specified passband Used to assess energy distribution and channel response
Working angle Nominal incidence angle and angular spread Confirmed against mounting and beam convergence
Polarisation Unpolarised, S/P or specified Especially for oblique-incidence structures
Substrate and thickness Assessed for spectrum, strength and assembly UV and NIR absorption characteristics depend on the specific material
Outline and clear aperture Per holder or filter wheel drawing Distinguish the outline dimension from the guaranteed performance area
Surface and edge Defect, chamfer and chip requirements Agreed by optical path and assembly use
Inspection and delivery Spectra, dimensions, appearance, batch documents State measurement conditions and sampling scheme

A filter specification has to match the position where it is used. The same interference filter can show a different spectral response at a different angle, cone angle or polarisation state. Confirm the spectral target together with the optical path conditions, not just the centre wavelength and size.

Element 1 Element 2 Element 3 short segment middle segment long segment switch switch short wavelength → long ※ Design schematic, not measured data; switching intervals by agreement
Several filters covering different scan segments: segmented filtering and switching regions (design schematic, not measured data)

Four questions that decide instrument performance

These come up most often when matching a filter to a spectrophotometer.

Q1

Filter bandwidth is not instrument spectral bandwidth

The FWHM of a bandpass filter describes the filter curve itself. The spectral bandwidth of a scanning spectrophotometer depends on slits, dispersion and the optical system, so the filter bandwidth cannot replace the instrument specification. In modules that use a filter as the main selector, the response still depends on source, filter and detector together.

Q2

Narrower is not automatically better

A narrower band may separate fine spectral features better but also reduces collected energy. Decide against the sample absorption profile, signal-to-noise ratio and measurement method rather than pursuing the smallest bandwidth.

Q3

Single-part OD is not the instrument stray-light figure

Filter OD describes attenuation under specified conditions. Instrument stray light also depends on grating scatter, structural light leaks, reflections and the detector. Meeting the filter specification still requires checking performance in the real instrument.

Q4

After changing a filter, check baseline and switching region

Even at the same nominal band, a different edge, transmission or thickness can change the system response. After replacement, check baseline, throughput, stray light and continuity in the switching region.

Applications and adaptation points

Different photometric instrument formats place different requirements on the filter solution.

Application Main need Filter design focus
UV–Vis scanning spectrophotometers Continuous scanning and photometric measurement Order sorting, out-of-band rejection, switch matching
UV–Vis–NIR instruments Wide-range scanning and multiple detectors Segmented filtering matched to different response regions
Fixed-wavelength photometric modules One or a few detection bands Bandpass selection and channel consistency
Water quality and chemical analysis modules Absorbance change for a specific method Detection band matched to the reagent system
Biochemical and laboratory photometric modules Multi-wavelength switching and batch measurement Filter sets, wheel fit and batch consistency
Instrument development and test platforms Intensity adjustment and performance checks Neutral density filters and suitable reference elements

The same filter can behave differently in different instruments; the table describes design directions and the final specification is agreed per project.

Internal filters versus verification reference filters

The two serve different purposes and cannot replace each other.

In the path

Internal instrument filter

Selects wavelengths, suppresses non-target light or adjusts energy; it is part of the optical path.

Metrology

Verification reference filter or standard

Checks wavelength, photometric or stray-light performance and requires applicable reference values, measurement conditions, certificates and traceability.

An ordinary fabricated filter cannot serve as a calibration standard on the strength of its name or nominal OD. For example, stray-light checks on a spectrophotometer may use a suitable reference material with a steep cut-off characteristic, whose purpose differs from that of the internal stray-light suppression filter.

Custom process

Instrument requirement review → spectral design → mechanical matching → sample inspection → instrument validation → specification release

  1. 1

    Requirement review

    Instrument architecture, scan range, source, detector and filter function.

  2. 2

    Spectral design

    Define passband, blocking region, edges, transmission and permitted deviation.

  3. 3

    Mechanical matching

    Confirm size, clear aperture, incidence angle and filter wheel mounting.

  4. 4

    Sample inspection

    Check spectrum, dimensions, surface and marking.

  5. 5

    Instrument validation

    Check throughput, baseline, stray light and switching continuity.

  6. 6

    Specification release

    Issue drawings, acceptance criteria and batch inspection requirements.

Frequently asked questions

Source Factory In-house coating lines, no middlemen
Ready to Ship Standard items dispatched same or next day
Quality Guaranteed 100 % inspected, spectral report included
Express Delivery DHL / FedEx worldwide