ISO 9001 Certified Manufacturer 360° Factory Tour
Wiki & Glossary

Coating Durability: Wiping, Damp Heat, Salt Fog and Thermal Cycling

· 2 views · 2 min read · OOTEE Optics Editorial

Original content by the OOTEE Optics editorial team, drawn from first-hand production line and inspection data. Please credit the source when republishing.

Given limits in expertise and test conditions, the theories, parameters and conclusions here carry no guarantee of absolute accuracy. For technical learning and exchange only - never the sole basis for design, acceptance or selection. Corrections welcome.

Coating Durability: Wiping, Damp Heat, Salt Fog and Thermal Cycling

Coating durability describes how well a film survives wiping, damp heat, salt fog and temperature change. It does not appear on the spectral curve, yet it decides how long the part lasts once installed.

Many "sample passes, production fails gradually" stories trace back to exactly this.

Common tests

TestTypical conditionWhat is checked
Adhesion (tape test)Specified tape applied and pulled off sharplyPeeling or detachment of the film
AbrasionCloth or eraser rubbed for a set number of strokes at set pressureScratches and film damage
Damp heate.g. 40 C / 90% RH for 48-240 hoursWavelength drift, transmission change, appearance
Thermal cyclinge.g. -40 C to +85 C for 5-50 cyclesCracking, delamination, wavelength drift
Salt fog5% NaCl fog for 24-96 hoursCorrosion and discoloration
Solvent resistanceWiping with alcohol, acetone and similarDissolution or hazing of the film

Typical governing standards include MIL-C-48497 (US military coating standard), the ISO 9211 series for optical coatings and GB/T 26332 in China, plus sector-specific standards.

Judging: appearance, but above all spectrum

Many vendors only inspect appearance. What really matters is the spectral comparison before and after:

  1. Center wavelength drift: how many nanometers after damp heat? Soft coatings may drift 1-2 nm; hard coatings should stay under 0.5 nm.
  2. Transmission loss: any drop beyond 2-3 points deserves scrutiny.
  3. Blocking degradation: has the OD value fallen, letting more light leak?
  4. Appearance: blistering, peeling, pitting, hazing, discoloration.

Ask for before-and-after measured curves - the most convincing evidence available.

What matters in each application

  • Indoor instruments (labs, production lines): routine adhesion and abrasion; damp heat can be relaxed.
  • Outdoor equipment (security, traffic, environmental monitoring): damp heat plus thermal cycling plus UV ageing assessment.
  • Automotive: the toughest thermal shock (-40 to +85 C or even +105 C), usually against automotive reliability standards.
  • Medical and food: resistance to chemical disinfection (alcohol, chlorine agents) and repeated wiping.
  • Marine and chemical: salt fog is a hard gate.

Three ways to improve durability

  1. Use a hard process: IAD or sputtered films are dense and void free, so water uptake and oxidation drop sharply.
  2. Add a protective layer: a top layer of SiO2 or Al2O3 improves wipe and corrosion resistance.
  3. Seal the edge: in extreme environments, edge coating or a retaining ring keeps moisture from wicking in from the side.

Writing the requirement

Three elements, none optional: standard + condition or duration + pass threshold.

Example: "Per the relevant ISO 9211 / MIL-C-48497 tests: after 96 hours at 40 C and 90% RH, center wavelength drift no more than 0.5 nm, peak transmission loss no more than 2%, no peeling or pitting; after 20 cycles from -40 to +85 C, no cracking or delamination."

A sentence like "must be durable" carries no obligation at all and will not be acted on.

Need a test plan for your application? Send the environment, temperature and humidity range and lifetime target to sales@ootee.cn.

Related Reading

View all

Related Products

View all products

Need a custom optical filter?

Send us your drawing and spectral targets — an engineer replies with a feasibility check and quotation within one business day.

Source Factory In-house coating lines, no middlemen
Ready to Ship Standard items dispatched same or next day
Quality Guaranteed 100 % inspected, spectral report included
Express Delivery DHL / FedEx worldwide